3500 and 3500B High Displacement Engines for Caterpillar Built Machines Transmission Oil Cooler - Remove and Install Caterpillar


Transmission Oil Cooler - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the cooling system coolant into a suitable container for storage or disposal.


    Illustration 1g01052354

  2. Remove bolts (1). Remove elbow (2) and tube assembly (3).

  3. Attach a suitable lifting device onto the transmission oil cooler.


    Illustration 2g00917854

  4. Remove bolts (4). Remove bolts (5).


    Illustration 3g01052355

  5. Remove bolts (6) and remove transmission oil cooler (7). The weight of transmission oil cooler (7) is approximately 181 kg (400 lb).

Installation Procedure



    Illustration 4g01052355

  1. Attach a suitable lifting device onto transmission oil cooler (7). Install transmission oil cooler (7). The weight of transmission oil cooler (7) is approximately 181 kg (400 lb).

  2. Install bolts (6).


    Illustration 5g00917854

  3. Install bolts (5). Install bolts (4).


    Illustration 6g01052354

  4. Install tube assembly (3) and elbow (2). Install bolts (1).

  5. Fill the cooling system.

Information System:

550, 570 and 580 Wheel Harvesters Maintenance Interval Schedule
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Selector and Pressure Control Valve
550, 570 and 580 Wheel Harvesters Specifications
550, 570 and 580 Wheel Harvesters Safety Messages
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Work Tool Positioner - Adjust - Integrated Toolcarrier
140H and 160H Motor Graders Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Lift Kickout - Adjust - Integrated Toolcarrier
12H Motor Grader Engine Supplement Refrigerant Condenser - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Rear Drive Shaft
120H and 135H Motor Graders Machine Systems Bank Valve - Disassemble - Bank Valve with Hydraulic Detent
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Compressor - Remove and Install
3524B Engine for Caterpillar Built Machines Bearing Clearance - Check
320B, 320B L and 320B N Excavators Reference Material
R2900 Load Haul Dump Bucket Loading Hauling Units
CB-534D and CB-564D Asphalt Compactors Belts - Inspect/Adjust/Replace
R2900 Load Haul Dump Stopping the Machine
938G II Wheel Loader and IT38G II Integrated Toolcarrier Additional Messages
140H and 160H Motor Graders Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
143H and 163H Motor Graders 3176C Engine Supplement Battery - Remove and Install
R2900 Load Haul Dump Before Operation (Remote Control)
R2900 Load Haul Dump Operation (Remote Control)
R1600 Load Haul Dump Hydraulic System Relief Valve (Lift Circuit) - Test and Adjust