Battery - Remove and Install
`
143H and 163H Motor Graders 3176C Engine Supplement
[RENR4138]
ELECTRICAL AND STARTING SYSTEM
BATTERY GP
143H and 163H Motor Graders 3176C Engine Supplement
Battery - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
- Turn the engine start switch key to the OFF position. Turn all the switches to the OFF position.
- Turn the key for the battery disconnect switch to the OFF position. Remove the key.
- Disconnect the negative battery cable at the battery disconnect switch. The battery disconnect switch is connected to the machine frame.
Note: Do not allow the disconnected battery cable to contact the battery disconnect switch or the machine.
- Disconnect the negative battery cable (3) from battery (5) .
Show/hide table
![]() | |
Illustration 1 | g00993146 |
Show/hide table
![]() | |
Illustration 2 | g00993147 |
- Disconnect battery cable (6) from battery (5) .
- Remove locknuts (2). Remove battery hold down (1) .
- Use two people to remove battery (5). The weight of battery (5) is approximately 44 kg (97 lb). Disconnect battery cable (4) .
- Remove bolts (7) and remove battery hold down (8) .
- Use two people to remove battery (9). The weight of battery (9) is approximately 44 kg (97 lb).
Installation Procedure
- Use two people to install battery (9). The weight of battery (9) is approximately 44 kg (97 lb).
Show/hide table
![]() | |
Illustration 3 | g00993146 |
Show/hide table
![]() | |
Illustration 4 | g00993147 |
- Install battery hold down (8) and install bolts (7) .
- Use two people to install battery (5). The weight of battery (5) is approximately 44 kg (97 lb).
- Install battery hold down (1) and locknuts (2). Tighten locknuts (2) to a torque of 12 ± 3 N·m (9 ± 2 lb ft).
- Install battery cable (5) .
- Connect battery cable (6) to battery (5) .
- Connect the negative battery cable (3) to battery (5) .
- Install the key for the battery disconnect switch. Turn the battery disconnect switch to the ON position.
Information System:
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
140H and 160H Motor Graders Engine Supplement
Water Separator and Fuel Filter (Primary) - Remove and Install
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Additional Messages
R2900 Load Haul Dump
Stopping the Machine
CB-534D and CB-564D Asphalt Compactors
Belts - Inspect/Adjust/Replace
R2900 Load Haul Dump
Bucket Loading Hauling Units
320B, 320B L and 320B N Excavators
Reference Material
3524B Engine for Caterpillar Built Machines
Bearing Clearance - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Transmission Oil Cooler - Remove and Install
550, 570 and 580 Wheel Harvesters
Maintenance Interval Schedule
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems
Hydraulic Cylinder (Front Steering) - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train
Selector and Pressure Control Valve
R2900 Load Haul Dump
Before Operation (Remote Control)
R2900 Load Haul Dump
Operation (Remote Control)
R1600 Load Haul Dump Hydraulic System
Relief Valve (Lift Circuit) - Test and Adjust
R1600G Load Haul Dump Hydraulic System
Sequence Valve (Float) - Test and Adjust
14H Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Assemble
14H Motor Grader Power Train
Gear Pump (Transmission Charging and Scavenge) - Disassemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
2002/09/16
An Updated Air Starting Control Group Improves Durability of the Lines {5500, 5501}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System
Vane Pump (Implement, Pilot, Brake)
D350E Series II and D400E Series II Articulated Trucks Power Train
Output Transfer Gear Group
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems
Rollover Protective Structure (ROPS) - Remove and Install
140H and 160H Motor Graders Engine Supplement
Alternator - Remove and Install