New Routing of Wiring Harness for Pressure Sensor {1408, 5057, 6543}
`
2007/07/02
[SEPD0895]
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
- Track Feller Buncher:
- 1090 (S/N: BZJ205-2111)
- 1190 (S/N: BZK205-2162)
- 1190T (S/N: BZL205-2211)
- 1290T (S/N: BZM205-2260)
- 511 (S/N: 511265-286)
- 521 (S/N: 521295-315)
- 522 (S/N: 522235-247)
- 532 (S/N: 532175-176)
- TK711 (S/N: 101186-276)
- TK721 (S/N: 102187-367)
- TK722 (S/N: 103187-467)
- TK732 (S/N: 104186-549)
ReferenceRefer to Special Instruction, REHS4115, "Reworking the Pressure Sensor for the Saw Pump" for the rework procedure.
Description of Change: The wiring harness for the pressure sensor for the saw pump has been rerouted. The new routing prevents interference with the hood of the machine. This will extend the service life of the harness and the pressure sensor.
Adaptable To: The new routing of the harness for the 228-3649 Pressure Sensor is adaptable to the machines that are listed above.
The new routing of the harness for the 228-3649 Pressure Sensor is effective with the machines that are listed in Table 1.
Show/hide table
Model     | Serial Number     |
TK711     | S/N:101277-UP     |
TK721     | S/N:102368-UP     |
TK722     | S/N:103468-UP     |
TK732     | S/N:104550-UP     |
511     | S/N:511287-UP     |
521     | S/N:521316-UP     |
522     | S/N:522248-UP     |
532     | S/N:532177-UP     |
1090     | S/N:BZJ2110-UP     |
1190     | S/N:BZK2160-UP     |
1190T     | S/N:BZL2211-UP     |
1290T     | S/N:BZM2260-UP     |
Information System:
C15 and C18 Generator Set Engines
Radiator Top Tank - Remove and Install - Charge Air
AP655D and BG655D Asphalt Pavers Propel System
Piston Motor (Propel) - Steel Track Machine
160M and 160 Motor Grader Machine Systems
Bank Valve - Remove - Rear Frame
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Idler Axle - Disassemble
AP600D, AP655D, BG600D and BG655D Asphalt Pavers
MID 157 - CID 0967 - FMI 02
AP600D, AP655D, BG600D and BG655D Asphalt Pavers
MID 156 - CID 0967 - FMI 02
AP600D, AP655D, BG600D and BG655D Asphalt Pavers
MID 082 - CID 0967 - FMI 02
2007/07/09
New Installation Sleeves for the Transmission Clutches Are Now Available {0720, 3030, 3155}
C6.6 Engines for Caterpillar Built Machines
Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump
AP655D and BG655D Asphalt Pavers Propel System
Piston Pump (Propel) - Steel Track Machine
24M Motor Grader Power Train
Transmission Lubrication
AP655D and BG655D Asphalt Pavers Propel System
Location of Hydraulic Components (Propel System) - Steel Track Machine
C15 and C18 Generator Set Engines
Radiator Bottom Tank - Remove and Install - Charge Air
2007/08/06
Radiator and Hydraulic Oil Coolers Have Been Improved {1351}
C4.4 and C6.6 Engines for Caterpillar Built Machines
Low Power/Poor or No Response to Throttle
C4.4 and C6.6 Engines for Caterpillar Built Machines
Diagnostic Code Cross Reference
AP655D and BG655D Asphalt Pavers Propel System
Hydraulic Schematic (Propel System) - Steel Track Machine
587R Pipelayer Machine Systems
Boom Winch, Hook Winch and Winch Frame - Remove
587R Pipelayer Machine Systems
Boom Winch, Hook Winch and Winch Frame - Install
The Fitting on the Air Cleaner Group is Installed Incorrectly on Specific Off-Highway Trucks{1051}
CB14 Paving Compactor Machine Systems
Piston Pump (Propel) - Disassemble
CB14 Paving Compactor Machine Systems
Piston Pump (Propel) - Assemble
Reworking the Pressure Sensor for the Saw Pump{1408, 5057, 6543}
3412E Engine for Caterpillar Built Machines
Coolant Flow - Test