2002/09/16 New Pins for the Bulldozer Blade are Now Greased {6061, 6065, 6066} Caterpillar


New Pins for the Bulldozer Blade are Now Greased {6061, 6065, 6066}
`
2002/09/16 [SEPD0647]
IMPLEMENTS
BULLDOZER GP
2002/09/16 New Pins for the Bulldozer Blade are Now Greased {6061, 6065, 6066}
Landfill Compactor:
826G (S/N: 7LN1-UP)
826G Series II (S/N: AYH1-UP)
826H (S/N: AWF1-UP)
Wheel Dozer:
824G Series II (S/N: AWW1-UP)
824G (S/N: 4SN1-UP)
Service Magazine SEPD0674, September 2002, "New Pins for the Dozer Blade are Now Greased". Disregard this article. See the replacement article that follows.

Description of Change: A new mounting pin assembly is used on the machines that are listed. The new pin assembly is greased. The new greased pin assembly improves service life.

Adaptable To: The new pin assembly was effective with 824G Series II (S/N: AWW366-UP) Wheel Dozers, 826G Series II (S/N: AYH511-UP) and 826H AWF257-UP Landfill Compactors. The new pin assembly is adaptable to first production of the machines that are listed.

Note: Some machines near the serial number breaks may be equipped with the new pin or the accompanying bearing. The new pin is identified by the use of a grease fitting. The new bearing is identified by a grease groove. The bearing does not need to be replaced if the machine has the new bearing with the old pin.

Table 1
Parts List for 826G Landfill Compactors    
Part Number     Quantity     Description    
3B-8491     2     Grease Fitting    
8G-1097     2     Pin Assembly    
259-0422     2     Bearing    
136-2050     14     Spacer    
136-2051     4     Spacer    

Table 2
Parts List for 824G Landfill Compactors    
Part Number     Quantity     Description    
3B-8491     2     Grease Fitting    
118-0869     2     Pin Assembly    
259-0422     2     Bearing    
136-2050     14     Spacer    
136-2051     4     Spacer    
The bore for the pin in the loader frame must be welded. The hole in the loader frame should be bored in-line with the hole in the blade frame. Bore the hole to 76.13 ± 0.04 mm (2.997 ± 0.0016 inch) diameter. The mounting bolts and washers can be used again.


Illustration 1g00916585

Spacers should be installed in order to achieve a maximum clearance between the blade and the loader frame of 2 mm (0.08 inch).

Information System:

2003/04/21 A Sight Gauge for the Transmission Oil Level and an Oil Filler Tube at Ground Level are Available {3030}
Air Conditioning and Heating R-12 All Caterpillar Machines Machine Preparation for Disassembly and Assembly
574B Forwarder Power Train Power Train Charge System Pressure - Test
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Pulled Unit Hydraulics, Torque Converter, and Brake System Troubleshooting
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Hoist, Torque Converter, and Brake System Troubleshooting
R2900 Load Haul Dump Steering Control
2002/11/11 New Mirror Has Improved Durability and a New Support that Reduces Vibration {7319}
226 and 242 Skid Steer LoadersEngine Supplement Pump Mounting - Remove and Install
Bench Test Procedure for a 784B, 784C, 785, 785B, 785C,785D, 789, and 789B Off-Highway Truck Transmission{3030, 3073}
CB-534D, CB-534D XW and CB-564D Paving Compactors Machine Systems Radiator and Hydraulic Oil Cooler
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Electronic Control Module (Power Train)
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Proportional Pressure Solenoid Valve - Test
Air Conditioning and Heating R-12 All Caterpillar Machines General Information
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Trunnion - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines Refrigerant Compressor - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines Receiver-Dryer - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines Refrigerant Orifice Tube - Remove and Install
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Main Control Valve
R2900 Load Haul Dump Joystick Control
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pump - Remove
R2900 Load Haul Dump Autodig System - If Equipped
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
120H and 135H Motor Graders Machine Systems Air Control Valve (Parking Brake) - Assemble
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Transmission Control